烽火10GEPON OLT 命令行故障处理

rx_report_frames = 53366 rx_oam_frames = 313 tx_good_octets = 22461 tx_ucast_frames = 23 tx_mcast_frames = 0 tx_bcast_frames = 0 tx_gate_frames = 53366 tx_reg_frames = 0 tx_oam_frames = 313 rx_good_opi = 0 rx_bad_crc32 = 0 XG8A\\pon#

13.查看onu下是否环路 (能否自动下线)

配置ONU1的端口1的环回检测功能,检测时间间隔为10分钟。该ONU位于

槽位1的PON口1下。

Admin\\onu\\lan#set loop_detect slot 1 link 1 onu 1 port 1 status activated interval 600

set onu port loop detect ok! Admin\\onu\\lan#

在ONU1的端口1处应用环回检测配置。该ONU位于槽位1的PON口1下。 Admin\\onu\\lan#apply loop_detect slot 1 pon 1 onu 1 port 1 apply onu port loop detect ok! Admin\\onu\\lan#

查看ONU1的端口环回检测配置。该ONU位于槽位1的PON口1下 Admin\\onu\\lan#show loop_detect slot 6 pon 2 onu 1

~~~~~ ONU PORT LOOP DETECT, 6.2.1 ,ITEM=4~~~~~ PORT Status Interval(s)

~~~~ ~~~~~~~~~~~~ ~~~~~~~~~~~ 1 activated 60 2 activated 20 3 activated 20 4 activated 20 Admin\\onu\\lan#

14.onu历史告警查看命令

二、OLT(设备和多用户故障)

1.查看所有板卡,以及板卡型号,状态

Admin# sho version -------------------------------------------------

system device version is:V104R000

CARD NAME HARDVER SOFEVER

1 XG8A WKE2.201.075R1P RP0400 2 XG8A WKE2.201.075R1P RP0400 3 XG8A WKE2.201.075R1P RP0400 4 XG8A WKE2.201.075R1P RP0400

5 XG8A WKE2.201.075R1P RP0400 //XG8A在线版本RP0400

6 ---- ---- ---- // 不在线 7 ---- ---- ---- 8 ---- ---- ----

9 HSWA WKE2.115.334R1A RP1000 10 HSWA WKE2.115.334R1A RP1000 11 ---- ---- ---- 12 ---- ---- ---- 13 ---- ---- ---- 14 ---- ---- ---- 15 ---- ---- ---- 16 ---- ---- ---- 17 ---- ---- ----

18 ---- ---- ----

19 HU1A WKE2.170.846R3B1 RP0300 20 HU1A WKE2.170.846R3B1 RP0300 26 ---- ---- ---- Admin#

2.重启板卡命令

Admin# reboot 1 //重启1槽位板卡 Admin# reboot backup //重启备用主控盘 Admin# reboot system //重启所有板卡 Admin# reboot //重启整台设备

3.板卡在线时间以及板卡CPU利用率

Admin# sho time //主控盘运行时间

Now time is: Current Date is 2017-06-01 Current Time is 23:29:52 System running time is 13 day 09:33:39

XG8A# debug //XG8A运行时间 DEBUG_H> sho ru DEBUG_H> sho running_time System Up Time : 13 Days, 9 Hours, 44 Minutes, 37 Seconds.

Admin\\card#show card time slot 1 //查看线卡运行时间 CARD 1 TIMESHOW

Sys Date: 2016-03-29 13:40:17 Run Time: 0days 2h 39m 11s

Admin\\card#

Admin# sho usage

cpu usage: 9.93(%) //CPU利用率 memory usage: 87.38(%)

Admin\\card#show cpu-usage slot 16 //只能用于GPON板卡查看CPU利用率 ----- OLT CPU & Memory Using ----- CPU : 2.47%

Memory : 41.40% Admin\\card#

XG8A\\stats# sho cpu_usage //10GEPON板卡CPU利用率 Get CPU/MEM Usage result: OK!!! Object(0-0-0/553)

CPU Usage : 1.44%, Mem usage : 43.30%

4.复位PON口命令,查看PON口在线情况(历史离线)

Admin\\card#set slot 1 pon 1 disable //关闭PON口 set ok!

Admin\\card#set slot 1 pon 1 enable //打开PON口 set ok

查看PON口ONU在线情况

XG8A\\onu# sho auth ponno 2

NUM MAC CONFIG-TYPE ONU-NO ONU-STATE ---------------------------------------------------------------

1 d45f25eec20e OTH_ONU_2 1 SHUTDOWN

2 d45f25ee3e6e OTH_ONU_2 2 SHUTDOWN 3 d45f25eeb686 OTH_ONU_2 3 ONLINE 4 d45f25eedc7e OTH_ONU_2 4 ONLINE 5 c40938c087c8 OTH_ONU_2 5 ONLINE

5.上行端口状态和收发光功率

Admin\\device# sho uplink sl 19 p 1 //查看19:1上联口状态 Port info : 19:1

---------------------------------------------------------------------

------- port:<19:1> 's Configuration Information

Link state : Up Port state : Ena

bled AutoNegotiation : On Speed : 10000 Duplex : Full

Learning : Enabled FlowControl : Off Port VLAN ID : 4088

PriEn : Off PriValue : 0 interface mode : SERDES TRUNK : 1 Jumbo Frame : 2000

Admin\\device# sho uplink port_optical_info sl 19 po 1 //19:1上联口收发光情况 get uplinkcard 19 port 1 opticol info OK.

TX opticol power -2.33dBm. RX opticol power -2.98dBm. Opticol module bias 41.83mA. Opticol module tem 37.96℃. Opticol module VOL 3.26V. Opticol module S/N:SOURCEPHOTONICS Admin\\device#

6.上行口误码

暂无

7.上行口配置查看和修改方法(VLAN,双工,LACP等) 7.1、查看上行口状态

Admin\\device# SHO uplink slot 19 port 1 Port info : 19:1 ---------------------------------------------------------------------

------- port:<19:1> 's Configuration Information

Link state : Up Port state : Ena

bled AutoNegotiation : On

联系客服:779662525#qq.com(#替换为@) 苏ICP备20003344号-4